Samsung Washer Code U6 : What You Need To Be Doing!

Samsung Washer Code U6

Realizing that your washing machine isn’t working properly is alarming. One of the ways you could have discovered this could be after you see a display of an error code on your washer.

If you see the samsung washer u6 code on the display screen, this simply indicates that your washer is unbalanced. 

A quick way to fix this problem is to detect the origin of the issue and fix it accordingly

Willing to know how to go around this? Keep reading this article in order to find out!

What Does Samsung Washer Code u6 Mean?

First and foremost, there’s actually nothing like u6 code on a Samsung washing machine, the real and actual code is the “Ub error code“. 

A lot of users misinterpret this because of the way “ub” is displayed as “u6” on the washer display screen.

However, the error code is simply an indication that your washing machine is unstable or unbalanced. 

Often this can mean the appliance is not on an even surface or the laundry is not balanced in it.

You also need to know that this problem can also be triggered due to other technical issues which might be a little bit difficult but be rest assured, we’ll be highlighting them all in this article.

Before we dive into that, here’s a tabular illustration that shows you some common causes of the error code and easy ways to fix it.

Common CausesEasy Fixes
Uneven loads in the washerRearrange the loads properly and make them even.
Damaged leveling legsLocate the affected legs and replace 
Excessive or undersized laundry loadsReduce or increase the amount of loads.
Faulty suspension rodsReplace the faulty suspension rods
Damaged shock absorbersReplace the shock absorbers.

How To Fix U6 Code On Samsung Washer?

This problem can be caused by any of the following highlighted reasons below.

  • Uneven loads in the washer
  • Excessive or undersized laundry loads
  • Damaged leveling legs
  • Faulty internal components

#1. Excessive Or Undersized Laundry Load

samsung washer u6

Overloading the washer is one of the common things that can make the washer unbalanced. 

When excessive loads are placed in the drum or tub, it affects some components as it applies excess stress. 

But the unit pauses the wash cycle to prevent further damage.

In other cases, undersized laundry loads can also lead to your washer being unable to spin and results in lack of balance.

The laundry tends to accumulate on one side of the drum, putting the appliance off balance during a wash cycle and might show the u6 error code.

How to fix?

To fix this issue, you need to reduce the amount of laundry you put in your washer. 

A good idea is to remove some bulky laundry items such as bed sheets, blankets, curtains, duvets, doonas or delicate and embellished clothes.

You can then proceed to wash these items separately.

  • So your washer is underloaded when the tub is ⅓ full and it tends to get overloaded when over ¾ full.
  • To find an accurate balance, we recommend that you fill the washer in the ½ full to ¾ full arena.

Doing this will ensure that your washer gets back to normal then you can reset and restart the washer.

The error code should be cleared after doing this. 

#2. Uneven loads in the washer

Even after finding the accurate balance between excessive and undersized loads in your machine. 

u6 code on samsung washer

A problem can still arise if the loads are not evenly distributed in the tub.

A sign of uneven distribution of weight is if you notice intense shaking and loud sounds. 

Some washing machines are so smart that they can quickly detect when the load is not evenly distributed, which is why the error code is displayed.

How to fix?

What you need to do is check the distribution of laundry in the washing machine drum. 

This also usually happens if you’re washing one large item such as a pillow.

Correct the load if the laundry is stuck to one side or tangled. 

Another quick fix is to add or remove the laundries you think might be causing an unbalanced weight.

#3. Damaged Leveling Legs

U6 error code on Samsung washing machine

Your washer leveling legs are very important for the overall stability of your washer, especially during a wash or spin cycle.

If these legs are either broken or damaged, it can cause the appliance to get unbalanced on the surface.

Fortunately, you can easily detect bad leveling legs visually without any technical experience.

How to fix?

The leveling legs are usually located on the base of your washer and it doesn’t necessarily need dismantling to repair.

Follow the procedures to fix this problem.

  • With a flashlight, inspect the legs but looking for cracks or any missing legs.
  • Find the legs that are probably incorrectly adjusted.
  • If you see any signs of wear or damage, then you might need to remove and replace the affected legs.

#4. Faulty Internal Components

u6 samsung washer

Note that some damages to internal components can also be a reason for the error code display.

But they’re not as common as others that have been previously highlighted above. 

As we continue, you should be aware that shock absorbers, suspension rods, straps, tub bearings and the control board are likely causes.

  • Faulty suspension rods – These components can also cause your washer to become unbalanced. It usually happens during the spin cycle if they’re damaged or worn out.

The suspension rods help support the tub and keep it balanced.

If the rods are not in a good condition or can no longer perform this function properly, it may cause the washer to display the Samsung U6 error code. 

To fix this issue, you need to replace the faulty suspension rods.

  • Damaged shock absorbers – If your samsung washer is a front-loading type, then you should have a shock absorber in it. Shock absorbers are basically for softening the movement of the drum and improving the effectiveness of your appliance.

A worn out shock absorber is not a common reason for the error code but it should be replaced if it’s damaged.

  • Tub bearings – The tub bearings is another potential reason why your washing machine might be unbalanced. This component is very important for keeping the inner tub of your washer spinning smoothly.

A defective tub bearing can interfere with the spin and balance of your washer which as a result leads to the u6 code on samsung washer.

  • Defective control board – Sometimes, your washer’s control board often malfunction, trigger  and send signals. Whenever this happens, you tend to see displays of error codes or an unusual output from your washer.

This simply indicates that a faulty control board is another reason why your washer might be displaying the code.

In situations like this, you need to troubleshoot the washer by replacing the panel and board.

How to Reset Samsung Washer Code U6?

To reset your Samsung washing machine if there’s a glitch with the control board or after attempting the above fixing guides.

Here are the resetting procedures you can take to reset the code and get your washer back up and running.

Unplug and Restart the run a spin only cycle.

Try unplugging your washer from the electrical outlet.

Doing this will help to clear any temporary glitches that may be resulting in the error code. 

Ensure to wait for a few minutes before plugging the washer back in. After doing this, run a spin only cycle while the washer is empty.

Final Thoughts

Want to learn more information regarding your washing machine, we’ve got you covered.

Below are some top articles you should definitely check out!

  1. Whirlpool Loc Error Washer? – Simple Fixes In 2023!
  2. E01 F03 Whirlpool Washer Error Code (Easy Fixes!)
  3. Say Goodbye to Maytag Washer Code 5d: (Fixes)

We hope you find this content helpful!

Fixing the samsung U6 error code is really easy if you follow the detailed guide we highlighted above. Best regards!

Leave a Reply

Your email address will not be published. Required fields are marked *

You May Also Like