In some cases, you may have encountered the 5d error code if you own a Maytag washing machine.
This error code can be confusing because it is often misread as “5d” when it is actually “SD.”
When there are too many suds in your washer, it can cause the appliance to stop working properly and trigger the display of the error code.
Perhaps you’re finding it difficult to clear this error, you’ll be provided with a detailed guideline on how to fix the problem in this article.
Let’s get started!
What Does maytag washer 5d code mean?
The 5d or SD error code is an indication that there are too many suds in your washer drum or tub.
This is usually caused by using too much detergent or probably the detergent you’re using is not a high-efficiency (HE) detergent.
With simplicity, the most common way to fix the issue is to reduce the amount of suds in the drum. You will need to do this by running the washer through a rinse cycle without any detergent.
First things first, let’s take a look at what could actually have led to the error code display.
How To Fix 5d Error Code Maytag Washer?
Below are the reasons why the error codes appeared on your display, before diving into the fixes.
- Technical glitch
- Using too much detergent.
- Using the wrong type of detergent
- Clogged drain pump & hose
- Damaged foam Level sensor
- Defective water pressure controller
- Faulty control panel
| What causes 5d error code | Quick Fixes |
| Technical glitches | Reset the washing machine |
| Excessive detergent | Reduce the amount of detergents |
| Blocked drain hose | Remove lints or debris in the hose and pump |
| Wrong type of detergent | Use high efficiency soaps |
| Damaged pressure switch | Replace the pressure switch |
| Faulty foam level sensor | You need to replace the sensor |
| Damaged control panel | Replace the control panel |
1. Technical Glitches
When your washing gets overworked to a certain extent, it tends to experience slight technical glitches.
This can cause the display screen to show some error codes by mistake even when the appliance is not actually defective.
How to fix?
The first thing to do in situations like this is to reset the washing machine. To initiate that, unplug the washer from the socket outlet.
Don’t immediately plug it back in! Wait for at least 60 seconds before plugging it in back.
This should reset the 5d code on maytag washer and get the washer back to normal.
Note that if this doesn’t work and the error code still displays, then the problem is probably due to more technical reasons which we’ll be highlighting ahead.
2. Excessive use of detergent
Using too much detergent is another reason why the 5d error code maytag washer is displayed. It’s important to make use of detergents, but you shouldn’t use too much.
Look up your user manual to know the correct amount of detergent you need to use.
How to fix?
Below are the two things you need to do to fix the error.
- Reduce the amount of detergent you use – Weigh up the quantity of detergents you use depending on the size of your laundry. Ensure that it’s not too much likewise not being insufficient. A normal proportion will not only eliminate the precise error codes but also get your clothes cleaned properly.
- Remove residual suds – You should get rid of residual detergent in the tub by running a “clean washer” cycle.
These processes shouId fix the problem, if not, move to the other causes below.
3. Using the wrong type of detergent
High efficiency is the recommended type of detergent that contains sufficient constituents needed for proper functioning of your washer.
If you are using the wrong type of detergent, this can lead to excessive suds in your washer which might potentially trigger the SD error code.
How to fix?
The way to fix this problem is to consider using high efficiency detergents. Most homeowners don’t actually realize the advantages of using HE detergents.
It effectively cleans your clothes while producing very little suds. Tide high efficiency detergent is a good example of that.
You can also use other recommended detergents as long as they are labeled as high efficiency.
4. Clogged Drain Pump and hose
When this drain pump or hose gets clogged, it prevents the flow of water and suds out of the washing machine.
Note that items left in our clothes and the residue of too much detergent can also damage and obstruct the drain pump.
If suds are unable to flow out of the washer, there’s no way the error code is getting cleared.
How to fix?
- Check if the hose is obstructed – Unplug the washer and disconnect the drain hose from both ends. Ensure that the hose isn’t kinked by straightening it out. You can use a metal to clean the inner surface to allow free water flow.
- Inspect the drain pump for blockage – Check and remove the lints or debris that may have been caught up in the drain pump filter. If the pump is damaged, you might need to find a replacement.
5. Damaged Water Pressure Switch
Another reason for the 5d or Sd error codes could be due to a faulty water pressure switch.
If the pressure switch is damaged, it could begin to send out incorrect signals to the washer which could have resulted in the error code.
How to fix?
The way to fix this if the pressure switch is damaged is to replace it by ordering a new one.
6. Inspect the Foam Level Sensor
It is important to inspect the foam whether it’s being too sensitive or not.
An oversensitive foam level sensor detects even a slight presence of suds inside the machine.
If you notice that the foam sensor is faulty or damaged, you might need to find a replacement so that you can get back to using your washer with no issues.
In case you don’t know how to detect a faulty foam level sensor, all you need is a multimeter to test the continuity.
This will tell you exactly if you need to replace it or not. Before trying to replace your foam level sensor, check out other fixes.
7. Malfunctioning Control Board
If after you’ve tried all the above fixes but the error code still keeps appearing, then the issue could be associated with the control board.
A faulty control panel could be the one triggering the constant display of the error message which might be really frustrating at times.
How to fix?
Replacing the control panel might be the best solution to this, but only if none of the aforementioned fixes seem to work.
Final Thoughts on 5d Maytag Washer
I hope we’ve been able to help you fix the code 5d on maytag washer. It doesn’t really have to be extremely different to do after reading the guide above.
If you have any questions, feel free to drop them in the content box while checking out some related contents below.
Related Contents:
2 comments
Where is the pressure sensor switch or foam level switch.
It’s attached to the interior of the washer’s rear panel under the main top or behind the control panel or under the top panel often.