Kenmore Washer Not Spinning Clothes Dry (2023 Fixes!)

Kenmore Washer Not Spinning Clothes Dry

Is your kenmore washer not spinning clothes dry? There are other numerous people experiencing this same issue and I can assure you that you’ll get a valid answer to your problem in this article below. 

Some of the main reasons why your kenmore washing machine isn’t spinning clothes dry is due to the use of excessive detergents, unbalanced loads, clogged drain hose, broken suspension springs or shock absorbers, faulty drive belt, lid motor coupling, damaged lid switch and many more.

In this article, we’ll be discussing the causes of this issue and an extensive guide on how to easily fix them in no time. 

Let’s dive into it!

Why Is My Kenmore Washer Not Spinning Clothes Dry?

Irrespective of whether you are using a top load or a front load type of washing machine, the spinning problem is generally common to both and we’ll be highlighting the top reasons and fixes in this particular section.

Here are the list of reasons why your kenmore washer won’t spin clothes dry:

#1. Excessive and Wrong Type Of Detergent

kenmore washer not spinning

Using too much of detergents creates a surplus of suds in your washing machine and can result in the wear down of the appliance. It also prevents the garment from rubbing against one another which is why your clothes are coming out dripping wet.

Also, you might be using some non-high efficiency detergents which is obviously resulting in the ineffective spinning of your washer. 

What you need to do? 

You need to be cautious of the amount and type of detergent you use for your kenmore washing machine.

It’s recommended that you use only suitable detergents according to the owner’s manual.

Although it might seem counterintuitive, but you should avoid using too much detergents in your laundry.

Note that the more detergent you use to a certain extent, the more dirtier your clothes will be and indirectly lead to spinning issues.

If there’s already too much of detergents in your washer, you can run the cleaning cycle by pressing the “Cycle” button a few times on your kenmore washer. 

#2. The Lid Switch Is Faulty Or Damaged

Kenmore washer won't spin

One of the components that might be affected if your washer won’t spin-dry correctly is the Lid switch. 

A damaged lid switch will prevent the appliance from spinning if the door isn’t getting closed properly. Also, the spin cycle definitely won’t start without locking the door 

How do you know if the lid switch is faulty? You can easily detect this by reading the continuity of the lid switch.

What you need to do?

To fix this, simply remove/unmount the lid switch and then proceed to use a multimeter to test the continuity.

We recommend setting your multimeter to the lowest ohms of resistance for an effective and accurate results.

If you detected no continuity on the lid lock switch, it definitely means it’s broken. Then you need to replace that specific component.

#3. The Load In The Washer Is Unbalanced 

If your kenmore washer isn’t spinning clothes dry, it could be because there is too heavy loads in it or the little loads you have aren’t balanced. 

Whenever unbalanced or heavy loads situation occurs, it prevents your washing machine from achieving proper spin speeds which is why your clothes still looks wet after completing a cycle.

What you need to do?

Ensure that the loads in the washer are evenly distributed in order to prevent spinning issues. Avoid putting all your bulky laundry inside the drum at the same time.

If you are using a front load kenmore washer, only pile your clothes up high but they shouldn’t pass the last row of holes at the front.

#4. Foreign Objects Are Trapped Inside

kenmore 80 series washer not spinning

Depending on the size or weight of the trapped items in your washing machine drum, it can literally affect your washer.

If clothes are getting stuck or objects getting trapped, it could be part of the reasons why your kenmore washer won’t spin dry as it should.

But how exactly do these objects get trapped in your washing machine, it gets inside as a result of the foreign objects you left behind in your trouser’s pockets or other clothes and materials.

What you need to do?

In order to fix this, here are some procedures you need to take:

  • Empty your washing machine drum by removing all the clothes inside in order to easily get access to the interior. Check the drum carefully for any foreign objects that might be making it to malfunction.
  • You can also use a flashlight to help you find some of these tiny objects easily. Once you find them, use a pair of pliers or tweezers to get them out without scratching the inner of your drum.
  • If you have any clothes that are getting stuck because they have lots of buttons attached to them or due to their texture for instance, you should take them out and wash them separately afterwards.

Your kenmore washing machine should start spinning properly after doing this.

#5. Applying Incorrect Spin Settings

Knowing how to set the correct spin settings is very important if you want to your washer to spin dry properly. 

Note that if you have selected an incorrect spin dry settings, your washer might not spin-dry your clothes properly which could leave them wet and take longer time to dry.

What you need to do?

Make sure you’re choosing the correct settings depending on the type of clothes you are washing and the weight of the load.

For delicate and light-weight clothes, you should set a spin speed around 400 – 600 RPM while medium-weight clothes should be around 800 – 1000 RPM.

Heavier fabrics like jeans or towels should be a little bit higher around 1200 – 1400 spin speed.

However, in general, note all kenmore washing machine models might not have this feature.

#6. The Drain Hose Is Clogged And The Pump Is Broken

You can begin to experience excessive water retention or improper drainage if your washing machine drain hose is clogged. 

kenmore series 500 washer not spinning

A blocked drain hose won’t let water drain properly, leading to a backflow and even cause your clothes to retain excess water. 

In other words, your kenmore washer won’t spin clothes dry if all these are occuring. A clogged drain pump also contributes to this issue. 

If the pump filter of your washer is blocked with lints or the pump is broken, it’ll definitely obstruct the flow of dirty water and as a results end up affecting the proper spinning of the machine.

What you need to do?

You need to troubleshoot the drainage system by checking and inspecting both the drain hose and drain pump.

Inspect the drain hose: Ensure that you’ve unplugged the washing machine first. Now, remove the drain hose which is located at the back of your washer.

Check if there are any blockages or clogs inside, clean and reattach.

Additionally, if the hose is also kinked, you need to straighten it out in order to allow proper water flow.

Inspect the drain pump and filter: Get rid of any lint or debris that might be clogging the filter then replace the drain pump if it’s broken.

#7. The Drive Belt Is Loosen Or Broken

The drive belt actually control and determines the entire spinning of your washing machine. 

If it gets loose or damaged, you will begin to experience problems like preventing the motor from turning the drum, the washer not spinning clothes dry and many more.

What you need to do?

It’s time to replace the drive belt so you can fix the problem. In order to replace the drive belt on your kenmore washer, here’s what you are required to do below:

  • First and foremost, unplug your washer or disconnect from switch. Also shut off the water supply.
  • Remove the access panel on the back of the washing machine.
  • Now, locate the belt and remove it from the pulleys.
  • Next, install a new drive belt by threading it through the pulleys before plugging your washer back.

#8. The Motor Coupling And Water Inlet Valve Are Faulty

Most of the time, your washer always begins to malfunction when a component or two becomes faulty.

For instance, a motor coupling and water inlet valve are two very vital components that transfers power from the motor to the agitator and controls the flow of water into the machine respectively.

If any of these components gets damaged, it could lead to spinning problems which is why we recommend inspecting them if your kenmore washer won’t spin clothes dry.

Use a multimeter to test the continuity, if no continuity is detected, you should replace the components as soon as possible.

kenmore series 110 washer not spinning

How To Enter Diagnostic Mode On A Kenmore Washer?

You can decide to troubleshoot the washing machine via diagnosis if you are yet to figure out the root of the problem. Follow the procedures below to activate the diagnostic mode on your kenmore washer.

  1. Ensure that the appliance is in standby mode which simply means that there should be no indicators illuminating at the moment.
  1. Choose any three button to press on the control panel except the “Power” and “Start/Stop” button.
  1. For instance, you can choose to press the “Wash Temp”, “Soil Level” and “Spin Speed” buttons.
  1. Now, press and hold these three buttons simultaneously for three seconds before releasing them.
  1. Next, immediately press those three buttons again & hold for another three seconds. Then, release the buttons. 

All indicators should be illuminated and that’s how to activate the diagnostic mode

Frequently Asked Questions

Q1: Kenmore Series 500 Washer Not Spinning Clothes Dry?

If your kenmore series 500 washing machine isn’t spinning as it should, you need to inspect the clutch assembly to see if it’s damaged or not. 

Reduce the amount of detergents you are using in the washer, check for a loose drive belt before replacing. Remove loads that are too heavy in the washer and only set the correct spin settings.

Q2: Kenmore 110 Series Washing Machine Won’t Spin Clothes Dry?

Kenmore 110 series washer models also do get affected by not spinning-dry problems, what you need to do is check if the lid motor coupling is broken, inspect if the drain pump hose or filter is kinked or clogged.

Other areas to inspect are the transmission, to check if it’s malfunctioning or has seized up. Ensure that the loads in the washer are perfectly balanced and should not be too much.

Checking for a clogged drain pump, broken washer belt and suspension springs are also important.

Q3: Kenmore 80 Series Washer Not Spinning Clothes Dry?

Your kenmore 80 series washer is not spinning clothes dry because the suspension springs or shock absorbers are worn out, there are unbalanced loads in the washer, too much detergents, damaged drive belt and incorrect spinning settings.

Q4: Kenmore Elite Washer Not Spinning Clothes Dry?

Below are some fixes to carry out it your kenmore elite washer won’t spin clothes dry:

Use appropriate spin settings, check for debris and clogs in the drain hose or and filter.

Fix or replace the lid switch if it’s broken, avoid excessive use of detergents and only use the recommended type.

Additionally, check if there are too much loads in the washing machine then reduce it to the minimal.

Q5: Kenmore Front Load Washer Not Spinning Clothes Dry?

In order for your kenmore front load washer to start spinning-dry perfectly, you need to ensure that there’s a limited amount of recommended detergents in the drum. 

Check for any foreign objects blockages, drain hose should be free from clogs and debris in addition to the drain filter.

If none of the above fixes work, then you need to divert your attention to the control panel.

If the control panel seems damaged or faulty, you might definitely want to find a replacement.

Q6: Kenmore Top Load Washer Not Spinning Clothes Dry

Kenmore top load washing machines usually experience spinning issues because their lid switch is not functioning properly which obviously needs replacement. 

Inspect the drive belt and motor coupling for any damages, also check the agitator and the clutch if it’s broken. 

Final Thoughts

We honestly hope you were able to fix your kenmore washer that refuses to spin dry properly with the help of our extensive guide above. 

Perhaps you’re still experiencing the same problem, do well to check out our related guides otherwise reach out to the manufacturer of the washing machine for additional assistance.

Related posts:

Leave a Reply

Your email address will not be published. Required fields are marked *

You May Also Like